Operators ManualCS9CS13Models:Please read these instructions carefully and makesure you understand them before using the machine.MANUAL NO. 111315 REV
10ASSEMBLY9. With the hood open, secure the (3) bags inplace. The back of the bags will hook overthe mounting tabs on the hitch assembly.Figure 5.10.
11ASSEMBLYBlower/Drive Kit1. Open the drive kit box and remove all ofthe components.2. Place the deck in the lowest cuttingheight.3. Remove the right
12ASSEMBLY12. Position the belt guide approximately 1/8"away from the belt. Re-tighten the 3/8" nut.13. Re-install the pulley cover and 1/4
13OPERATIONOperating the Collection System1. NEVER USE THE COLLECTION SYSTEMWITHOUT THE BLOWER ASSEMBLYAND HOSES SECURELY ATTACHED.2. Make sure hoses
14SERVICE AND MAINTENANCE Preventative Maintenance Schedule Item Before
15SERVICE AND MAINTENANCECaring For Hoses1. Inspect hoses before each use. If hoses haveexcessive wear, tears, or punctures, replaceimmediately.2. To
16SERVICE AND MAINTENANCE PROBLEM POSSIBLE CAUSE CORRECTION Loss of Vacuum. 1. Blower, ho
17NOTE: Your Front Weight Bar may look different from those shown in this diagram.SPINDLE DRIVE ASSEMBLY
18HOOD ASSEMBLY123456789101112131415161718192210205231923232123201424
19ITEM PART NO. QTY DESCRIPTION1 ... 111172 ... 1...HOOD2 ... 111174 ...1...HOOD SUPPORT3
2©2005 Yazoo/Kees Power Equipment. All Rights Reserved.Beatrice, NE. Printed in U.S.A.
20HITCH ASSEMBLY123456789101112131415151718192016151115111511
21ITEM PART NO. QTY DESCRIPTION1 ... 111155 ... 1...HITCH2 ... 111190 ... 1...LATCH3 ...
22BLOWER ASSEMBLYLOCKING COLLARTHIS SIDE UPTHIS SIDE DOWNHUB DOWN1234567891011121314151617181920212223242526272829303132333435363738394041424363636376
23BLOWER ASSEMBLYITEM PART NO. QTY DESCRIPTION1 ... 111331 ... 1...FAN COVER W/DECALS2 ... 108941 ...
24WEIGHT KITITEM PART NO. QTY DESCRIPTION1 ... 20255 ... 1...WEIGHT BAR, FRONT2 ... 111313 ...
25WEIGHT KITMODEL CS9ITEM PART NO. QTY DESCRIPTION1 ... 111313 ... 1...HOLD DOWN, WEIGHT BAR2 ... 102049 .
26MOUNTING KIT12345678910111213141516171819202191214REF.MODEL CS13
27ITEM PART NO. QTY DESCRIPTION1 ... 111322 ... 1...HITCH BRACKET, RIGHT, W/DECAL... 111199 ...
28MOUNTING KITMODEL CS9123456781112131415161718192021222314166REF.
29ITEM PART NO. QTY DESCRIPTION1 ... 111294 ... 1...HITCH BRACKET W/DECALS, RIGHT... 111203 ...
3WARNING: Engine exhaust, some of its constituents, and certain vehicle components con-tain or emit chemicals known to the State of California to caus
30BAG ASSEMBLYITEM PART NO. QTY DESCRIPTION1 ... 110063... 1...HANGER, BAG2 ... 111166 ... 1...
31DRIVE KIT ASSEMBLY111295 - 48 INCH DECKITEM PART NO. QTY DESCRIPTION1 ... 111254 ... 1...SHIELD W/DECALS, 48”
32DRIVE KIT ASSEMBLY111296 - 52 INCH DECKITEM PART NO. QTY DESCRIPTION1 ... 111268 ... 1...SHIELD W/DECALS, 52”
33DRIVE KIT ASSEMBLY111297 - 61 INCH DECKITEM PART NO. QTY DESCRIPTION1 ... 111269 ... 1...SHIELD W/DECALS, 61”
4FEATURES & CONTROLSNOTE: Your Front Weight Bar may look different from those shown in this diagram.BLOWER ASSEMBLYHOSEBAGREAR GUARDCAST WEIGHTWE
5SAFETY RULESSafety Procedures1 - Training:• Read the Operator’s manual. If the operator(s)or mechanic(s) can not read English it is theowner’s respo
6SAFETY RULES3 - Operation• Never run an engine in an enclosed area.• Only operate in good light, keeping away fromholes and hidden hazards.• Slow dow
7ASSEMBLYUnpacking InstructionsAssembly InstructionsCollection SystemTools Required:RatchetTorque Wrench1/2" Wrench1/2" Socket9/16" Wre
8ASSEMBLY4. Remove the (10) 5/16 carriage bolts thatsecure the standard rear guard to the strapsand skid plates. Remove the standard rearguard. Repl
9ASSEMBLY7. Place the hood assembly on to the hitchassembly. Place both hood hinges betweenthe upper hitch mounts on the hitch assembly.Be sure that
Commentaires sur ces manuels